In PY 2014, IDP completed the design and fabrication of a Foro 1650 Drill (previously referred to as the Intermediate Depth Drill or IDD). With assistance from international colleagues, IDP modified the existing design of the Hans Tausen Drill and built a new system. The system was field-tested outside of Summit Station, Greenland, in spring 2014 and was used in the successful completion of the SPICEcore project near South Pole Station from 2014-2016, where a total of 1,751 m of core was collected. The drill was originally designed to reach a depth of 1,500 m. Following a post-project analysis of the SPICEcore project, IDP has set the cable limit for the current winch drum at 1,700 m capacity, which allows for drilling to approximately 1,650 m depth. This maintains adequate safety margins for the drum flanges and mitigates the risk of system damage should the level wind not spool the cable perfectly every time. While the system was originally called the Intermediate Depth Drill or IDD, the name was updated in 2019 to signify the shared sonde design of other IDP drill systems (e.g. Foro 400, Foro 3000). IDP also procured new 4-conductor cables following the SPICEcore project to mitigate operational issues experienced during the project. IDP also pursued a resign of the drill system electronics to implement beneficial sensors for temperature, pressure, and inclination. The drill system electronics design is now shared between the Foro 1650 and the Foro 3000, making use of proven, off-the-shelf parts wherever possible.
Equipment Details
| Name | Foro 1650 Drill |
|---|---|
| Type |
Type
Ice coring
|
| Number in Inventory |
Number in Inventory
1
|
| Max. Practical Depth |
Max. Practical Depth
1650 m
|
| Hole Diameter |
Hole Diameter
129.6 mm (wet hole)
126 mm (dry hole)
|
| Ice Core Diameter |
Ice Core Diameter
98 mm (3.85 inches)
|
| Ice Core Length |
Ice Core Length
2.0 m
|
| Rock Core Diameter |
Rock Core Diameter
[NA]
|
| Rock Core Length |
Rock Core Length
[NA]
|
| IDP Driller Required? |
IDP Driller Required?
Yes, 3+ (number of drillers required depends on desired drilling depth and drilling schedule)
|
| Drill Fluid Required? |
Drill Fluid Required?
Yes
|
| Trench Required? |
Trench Required?
Yes |
| Power Requirements/Source |
Power Requirements/Source
35 kW, 460 V, 3-phase generator
|
| Estimated Drilling Time |
Estimated Drilling Time
1,500 m - 85 days (assumes 24 hour operations) |
| Helicopter Transportable? |
Helicopter Transportable?
Yes (see system weight/cube below)
|
| Light Aircraft Transportable? |
Light Aircraft Transportable?
Yes (see system weight/cube below)
|
| Shipping Weight |
Shipping Weight
27,000 lbs (does not include drilling fluid, generator, generator fuel, or personnel) |
| Shipping Volume (Cube) |
Shipping Cube
1,875 |
Documents
| Citation | Year |
|---|---|
| Eric Saltzman, Eric J Steig, IDPO (2011) Intermediate Ice Coring Drill - Science Requirements. 1-2. | 2011 |
Photos
The very last run of ice from the South Pole Ice Core project inside the barrel of the Intermediate Depth Drill. The ice is from 1751 meters depth. Credit: Jay Johnson
The drill head of the Intermediate Depth Drill with a core inside the drill barrel. The rotating drill head contains three razor sharp cutters that shave out an annulus of ice, which the drill then slides down into. As the drill slides down into the annulus it slides over the core, which is 98 mm (3.86 inches) in diameter. When a cable pulls up the drill, three cams grab the core and break it free. After the drill is pulled back to the surface it is lowered from a vertical to horizontal orientation so that the ice core can be removed from the drill barrel. Credit: T.J. Fudge
Drillers remove the inner barrel from the outer barrel of the IDD. The drilled run of ice core is then pushed out of the inner barrel. Credit: Murat Aydin
Mindy Nicewonger at the core processing station inside the drill tent for the South Pole Ice Core project. The IDD recovers ice cores approximately 2-meters in length. The 2-meter long sections of core are then cut into 1-meter long sections so that they fit into the standard-sized insulated shipping container (ISC) boxes used by the US ice-coring community to transport ice cores. A dry-cut circular saw is used to make the cuts. Credit: Murat Aydin
A close-up view of an ice core still in the IDD's drill barrel. Credit: Peter Rejcek
Inside the drilling tent of the South Pole Ice Core project during the 2014-2015 summer field season. The Intermediate Depth Drill was purpose-built for coring 1,500 meters of ice. Credit: Peter Rejcek
Science team members work in the South Pole Ice Core drill tent, cleaning the drill and measuring ice cores. Credit: Peter Rejcek
Moving ice cores up out of the South Pole Ice Core project's core storage trench to ready them for transport to McMurdo Station. Credit: Jay Johnson
The lift system used to move ice cores up out of the South Pole Ice Core project's core storage trench. Credit: Jay Johnson
View of the inside of the South Pole Ice Core project's core storage trench after all of the 2-meter-long sections of brittle ice were cut into 1-meter-long sections and packed into the white ISC boxes. Credit: Joseph Souney
View of the South Pole Ice Core field camp, located a few kilometers from the Amundsen-Scott South Pole Station. The IDD was housed within the long red and white arched tent. Credit: Peter Rejcek
View of the South Pole Ice Core field camp, located a few kilometers from the Amundsen-Scott South Pole Station. The IDD was housed within the long red and white arched tent. Credit: Peter Rejcek
Cutting the 2-meter long sections of brittle ice into 1-meter long sections during the 2015-2016 summer field season of the South Pole Ice Core project. Credit: Jay Johnson
The IDD returns to the surface after retrieving an ice core for the South Pole Ice Core project during the 2014-2015 summer field season. Credit: Peter Rejcek